Skip to content
Emergency Plumbing emergency? Call us, we answer. Call us, we answer 4.9 · 104 Google reviews Garland, TX (903) 865-2942
Garbage Disposal Installation in Garland

Garbage Disposal Installation in Garland

Licensed Garland plumbers who install it right, clean up after, and answer the phone.

Call or text (903) 865-2942

Request an estimate

Tell us what you need

No obligation


By submitting this form you agree that we may contact you about your request and share your name and email address with partner companies for email marketing. We never share your mobile number or text message consent with third parties or affiliates for marketing or promotional purposes.

Garbage disposal unit mounted under sink with plumbing connections and white drain pipes

4.9104 Google reviews

Overview

Disposal Installation Garland Homeowners Can Count On

Badgett Bros Plumbing handles garbage disposal installation in Garland, TX for homeowners who want the job plumbed correctly, the drain tested before we leave, and no mess left behind. If you're replacing a dead unit or adding a disposal to a sink that's never had one, call us at (903) 865-2942 and we'll walk you through what it takes before anyone touches a wrench.

What drives the cost of a disposal installation up or down isn't the unit itself; it's what we find when we get under the sink. A sink that already has the right drain configuration and a dedicated electrical outlet nearby is a straightforward swap. Add in a drain that needs reconfiguring, an outlet that doesn't exist yet, or mounting hardware that's corroded from Garland's hard water, and the scope grows. We'll tell you exactly what we're looking at before we start. Every job is different. Contact Badgett Bros Plumbing for an accurate estimate.

What Garbage Disposal Installation Involves

  • Remove the old unit and inspect the drain flange and mounting assembly
  • Set the new mounting ring with plumber's putty or gasket per manufacturer spec
  • Connect the discharge tube to the drain trap and test for leaks
  • Verify the electrical connection and run the disposal through a full test cycle
  • Clean the work area before we pack up
Black garbage disposal with white drain pipes and P-trap mounted under kitchen sink with LED light

Repair vs. Replace

Should You Repair or Replace Your Disposal?

Most homeowners aren't sure which call to make. Here's how we think about it.

  • Repair Makes Sense

    If the unit is fewer than eight years old and the problem is a jammed plate, a tripped reset button, or a leaking seal at the flange, repair is usually the right move. These are common fixes on otherwise sound units, and a garbage disposal repair visit is typically faster and cheaper than a full replacement.

  • Replacement Makes Sense

    A disposal that's grinding poorly, leaking from the bottom (not the flange), or making a loud metallic noise has a failed motor or cracked housing. At that point you're not repairing it; you're borrowing time. Units older than ten years in Garland homes often show heavy mineral scale from the area's hard water, which accelerates wear on the internal components.

  • When It's Neither

    Sometimes what looks like a disposal problem is a drain problem. A slow-draining sink after the disposal runs is usually a clogged line, not a failing unit. We'll check the drain line first so you're not buying a new disposal to fix a clog.

The Process

How We Handle Installation From Start to Finish

  1. Assess and Prep

    We check the existing drain configuration, the condition of the mounting flange, and confirm an accessible electrical connection. If the outlet isn't there or the drain needs rerouting, we tell you before work begins, not after.

  2. Install and Connect

    We set the mounting assembly, connect the discharge tube, and wire the unit properly. Reversed wiring on a disposal causes the motor to run backward and strips the internal shredder plate fast. We don't cut corners on the electrical side.

  3. Test and Clean Up

    We run water through the full drain path and cycle the disposal under load before we call it done. Then we clear the cabinet and wipe down the work area. You'll know immediately if something's off, not three days later.

Plumber or Electrician: Who Should Install Your Disposal?

The honest answer is: it depends on what's already there. If your sink has a dedicated 120V outlet under the cabinet, a licensed plumber handles the full installation. We manage the mounting, the drain plumbing, and the hardwire or cord connection. If there's no outlet at all and the job requires running a new circuit from the panel, that work crosses into licensed electrical territory. We'll tell you upfront which situation you're in. Most Garland homes with an existing disposal already have the outlet in place, so the installation stays in plumbing. Homes where a disposal is being added for the first time sometimes need an electrician first. We won't do work outside our license, and we won't tell you it's fine when it isn't.
Black Evolution Excel garbage disposal unit mounted under sink with white PVC drain pipes and plumbing connections

Common DIY Mistakes We Fix

These show up regularly on calls after a homeowner gave it a try.

Skipping the Plumber's Putty

The drain flange needs a proper seal. Without it, water works its way past the flange and drips inside the cabinet. It's a slow leak and homeowners often assume the disposal body is cracked before they find the actual source.

Wrong Drain Trap Configuration

A disposal discharge tube has to exit at the right height and angle to drain into the P-trap correctly. Get it wrong and you'll have standing water in the disposal chamber after every use. Persistent standing water is also a source of odor.

Reversed Wiring

Wiring a disposal with the hot and neutral reversed causes the motor to spin the wrong direction. It won't grind, it'll make noise, and it'll burn out the motor faster. This one's worth getting right the first time.

Over-Tightening the Mounting Ring

The snap-ring mounting system on most disposals has a specific torque range. Overtightened, it cracks the sink flange or distorts the mounting collar. We see it on stainless sinks fairly often, and fixing it means pulling the whole unit back out.

What Not to Put Down Your Disposal

A disposal is a motor and a shredder plate, not a trash can. These will break it.

No grease or cooking oil
It coats the grinding components and coats the drain line
No fibrous vegetables
Celery, artichokes, and corn husks wrap around the impeller
No expandable starches
Pasta, rice, and beans absorb water and pack the drain tight
No coffee grounds in volume
They settle into a dense paste and slow the drain line over time

Why Garland Homeowners Call Badgett Bros

Second-Generation Plumbers

We grew up in the trade. The two of us have seen every variation of this installation across Garland's housing stock, from newer builds off the George Bush Turnpike to older homes in North Garland where the drain configurations under the sink don't match anything on the box.

Fully Licensed and Insured in Texas

Every installation we do is performed by licensed plumbers. That matters for homeowner's insurance and for the work itself. We don't subcontract and we don't send unlicensed help on jobs.

104 Reviews, 4.9 Stars on Google

We haven't built that rating by overselling. Homeowners call us back because we told them the truth the first time and left the house clean. If a repair is the right answer, we'll say so instead of pushing a new installation.

Ready to Schedule Your Disposal Installation?

Call (903) 865-2942 and our office team will get you scheduled. We'll tell you what the job involves and what to expect before we schedule anything.

Call Our Office: (903) 865-2942

Frequently asked questions

Question not on the list?

(903) 865-2942

Ask the people who would do the work.

Are garbage disposals worth repairing?
It depends on the age and the failure type. A unit under eight years old with a leaking flange, a jammed plate, or a tripped reset is worth repairing. A unit over ten years old that's leaking from the bottom or grinding poorly likely has a failed motor or cracked housing, and repair costs at that point typically push close to replacement cost. We'll tell you which situation you're in before any work starts.
Do I need a plumber or an electrician to install a garbage disposal?
If the sink already has a dedicated 120V outlet under the cabinet, a licensed plumber handles the full job: mounting, drain plumbing, and the electrical connection. If no outlet exists and a new circuit needs to run from the panel, that portion requires a licensed electrician. Most Garland homes replacing an existing disposal already have the outlet in place. We'll check and tell you exactly what your kitchen needs.
How much does it cost to have a garbage disposal installed?
Cost depends on what we find under the sink: drain configuration, condition of the existing mounting hardware, whether the electrical outlet is in place, and the unit you've chosen. Homes in older Garland neighborhoods sometimes have mineral buildup or outdated drain setups that add scope. Every job is different. Contact Badgett Bros Plumbing at (903) 865-2942 for an accurate estimate.
What happens if I wire my garbage disposal backwards?
A disposal wired with the hot and neutral reversed will spin the shredder plate in the wrong direction. The unit won't grind food properly, it'll run louder than normal, and the motor will burn out prematurely. If you've installed a disposal that hums but doesn't grind, reversed wiring is one of the first things to check. We correct it as part of a service call.
Do I need plumber's putty for garbage disposal installation?
Most installations use plumber's putty around the drain flange to create a watertight seal between the flange and the sink basin. Some manufacturers specify a gasket instead of putty, particularly for composite or acrylic sinks where putty can stain. Skipping the seal entirely is the most common DIY mistake we correct: without it, water slowly leaks past the flange and drips inside the cabinet.
How do I know if my garbage disposal needs repair or replacement?
Leaks at the top of the unit near the flange, jams, and reset button trips are usually repair territory. Leaks from the bottom of the unit, a motor that hums without spinning, or loud metallic grinding noises typically mean the unit needs to be replaced. If you're not sure, call us and describe what it's doing. We'll help you figure out whether a repair visit or a full installation makes more financial sense.
What causes a garbage disposal to leak and how is it fixed?
Top leaks are almost always a failed flange seal or loose mounting bolts: fixable without replacing the unit. Side leaks usually mean a cracked discharge port or a failed gasket at the dishwasher connection, also repairable. Bottom leaks come from a cracked disposal body or failed internal seals in the motor housing: at that point replacement makes more sense than repair. Location of the leak tells most of the story.

Next step

Tell us about the job

Your name, your number and what needs doing. A person from Badgett Bros Plumbing gets back to you.

Rather talk now?(903) 865-2942

★★★★★

did everything promised and more. I would highly recommend them
Glenn B., Google review

Request an estimate

No obligation


By submitting this form you agree that we may contact you about your request and share your name and email address with partner companies for email marketing. We never share your mobile number or text message consent with third parties or affiliates for marketing or promotional purposes.

Updated November 2026